Difference between revisions of "MSM5205"
From Archaic Pixels
| Line 1: | Line 1: | ||
| − | + | Datasheet: [[File:MSM5205.pdf]] | |
| − | + | = Overview = | |
| − | + | The ADPCM playback hardware consists of the following components: | |
| − | The ADPCM playback hardware consists of the following: | + | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | MSM5205 | + | * ASIC (NEC gate array) containing ADPCM control logic. |
| + | * Oki MSM5205 ADPCM decoder (1 channel). | ||
| + | * Two M41464 DRAMs (64Kx4) for sample storage. | ||
| − | comes in an 18-pin plastic | + | |
| + | = MSM5205 pin assignments = | ||
| + | |||
| + | The MSM5205 comes in an 18-pin plastic DIP with "OKI M5205" stamped on it. | ||
[code] | [code] | ||
| − | + | +----v----+ | |
| − | + | S1 |01 18| Vdd | |
| − | + | S2 |02 17| /XT | |
| − | 4B / /3B | | + | 4B//3B |03 16| XT |
| − | + | D0 |04 15| RESET | |
| − | + | D1 |05 14| /VCK | |
| − | + | D2 |06 13| T2 | |
| − | + | D3 |07 12| T1 | |
| − | + | (N.C.) |08 11| (N.C.) | |
| − | + | Vss |09 10| DAOUT | |
| − | + | +---------+ | |
[/code] | [/code] | ||
| + | * S1 : Sample rate select input (1/2). | ||
| + | * S2 : Sample rate select input (2/2). | ||
| + | * 4B//3B: ADPCM data size. (0= 3-bit samples; set D0=GND, 1= 4-bit samples) | ||
| + | * D3-D0 : ADPCM data input. | ||
| + | * XT, /XT : Clock input, typically a 384 KHz ceramic resonator. If using an external oscillator, connect it to XT and leave /XT unconnected. | ||
| + | * /VCK : Output strobe that is triggered at the sample rate, used to latch D0-D3. | ||
| + | * RESET : Hold HIGH for at least two /VCK pulses to reset the chip. | ||
| + | * T1, T2 : Test mode pins (set T1=GND, T2= N.C.) | ||
| + | * DAOUT : Analog output from internal DAC. 5Vp-p @ Vdd=+5V. | ||
| − | |||
| − | |||
| − | |||
| − | + | Sample rate selection: | |
| + | [code] | ||
| + | S1 S2 | ||
| + | 0 0 : XT / 96 | ||
| + | 0 1 : XT / 64 | ||
| + | 1 0 : XT / 48 | ||
| + | 1 1 : (Not documented) | ||
| + | [/code] | ||
| + | For a 384 KHz clock source, these are 4, 6, and 8 KHz respectively. | ||
| − | + | = MSM5205 configuration = | |
| − | + | * 4B//3B tied to +5V (4-bit sample format selected) | |
| − | 48 | + | * S1 tied to +5V, S2 tied to GND (internal clock divider set to 48) |
| − | + | * Test mode pins are not used | |
| − | + | * ASIC drives XT, /RESET, and inputs /VCK. /XT is not used. | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | to determine how much playback time you get for each sample rate divide the total number of samples that can be contained in | + | = DRAM configuration = |
| − | + | ||
| + | The CPU interface to ADPCM RAM looks like a 64Kx8 array. However to the chip it is a 128Kx4 array, and samples can start on any nibble boundary. The sample length is always specified in byte (two-sample) units. | ||
| + | |||
| + | = MSM5205 timing = | ||
| + | |||
| + | Typically the MSM5205 is used with a 384 KHz resonator, and a divider of 48 provides an effective sample rate of exactly 8,000 Hz. However, the PCE implementation provides a programmable clock (effectively over- or underclocking the chip) to allow more sample rates to be selected. | ||
| + | |||
| + | The ASIC divides a 1.540,200 MHz clock to provide the clock signal fed to the MSM5205 XT pin. The divider is set by writing to the lower 4 bits of $180E: | ||
| + | [code] | ||
| + | $180E Divider XT frequency Sample rate (XT/48) | ||
| + | |||
| + | $00 16 96,270 Hz 2,005.46875 Hz | ||
| + | $01 15 102,680 Hz 2,139.166667 Hz | ||
| + | $02 14 110,020 Hz 2,292.083333 Hz | ||
| + | $03 13 118,480 Hz 2,468.333333 Hz | ||
| + | $04 12 128,350 Hz 2,673.958333 Hz | ||
| + | $05 11 140,020 Hz 2,917.083333 Hz | ||
| + | $06 10 154,020 Hz 3,208.75 Hz | ||
| + | $07 9 171,140 Hz 3,565.416667 Hz | ||
| + | $08 8 192,530 Hz 4,010.8375 Hz | ||
| + | $09 7 220,030 Hz 4,583.958333 Hz | ||
| + | $0A 6 256,700 Hz 5,347.916667 Hz | ||
| + | $0B 5 308,050 Hz 6,417.708333 Hz | ||
| + | $0C 4 385,050 Hz 8,021.875 Hz | ||
| + | $0D 3 513,400 Hz 10,695.8 Hz | ||
| + | $0E 2 770,100 Hz 16,043.75 Hz | ||
| + | $0F 1 1,540,200 Hz 32,087.5 Hz | ||
| + | [/code] | ||
| + | |||
| + | To determine how much playback time you get for each sample rate, divide the total number of samples that can be contained in RAM (131,072 samples) by the sample rate to get the playback time in seconds. | ||
| + | |||
| + | Note: According to the TurboDuo schematics there is a 9.21 MHz ceramic resonator connected to the ASIC. Assuming it is divided by 6 before being adjusted by $180E, that gives the base frequency of 1.535 MHz for ADPCM decoding. My measurements were at the XT pin, and seem to be close enough. | ||
| + | |||
| + | = ADPCM format = | ||
| + | |||
| + | The Oki ADPCM format is identical to the Intel/Dialogic VOX format. The 'Sound eXchange' utility ('sox') supports this format and the non-standard sample rates the PCE uses. | ||
| + | |||
| + | The VOX format has no header or other information to specify the sample rate, so that must be explictly stated during conversion. Some examples are as follows: | ||
| + | [code] | ||
| + | ; Convert 8 KHz ADPCM data to WAV file | ||
| + | sox -r 8000 test.vox test.wav | ||
| + | |||
| + | ; Convert WAV file to 32 KHz ADPCM data | ||
| + | sox music.wav -r 32000 music.vox | ||
| + | [/code] | ||
| − | + | The resulting headerless VOX file can be directly included into a program as binary data and stored to ADPCM RAM for playback. | |
Latest revision as of 09:56, 2 May 2014
Datasheet: File:MSM5205.pdf
Contents
Overview
The ADPCM playback hardware consists of the following components:
- ASIC (NEC gate array) containing ADPCM control logic.
- Oki MSM5205 ADPCM decoder (1 channel).
- Two M41464 DRAMs (64Kx4) for sample storage.
MSM5205 pin assignments
The MSM5205 comes in an 18-pin plastic DIP with "OKI M5205" stamped on it.
+----v----+
S1 |01 18| Vdd
S2 |02 17| /XT
4B//3B |03 16| XT
D0 |04 15| RESET
D1 |05 14| /VCK
D2 |06 13| T2
D3 |07 12| T1
(N.C.) |08 11| (N.C.)
Vss |09 10| DAOUT
+---------+
- S1 : Sample rate select input (1/2).
- S2 : Sample rate select input (2/2).
- 4B//3B: ADPCM data size. (0= 3-bit samples; set D0=GND, 1= 4-bit samples)
- D3-D0 : ADPCM data input.
- XT, /XT : Clock input, typically a 384 KHz ceramic resonator. If using an external oscillator, connect it to XT and leave /XT unconnected.
- /VCK : Output strobe that is triggered at the sample rate, used to latch D0-D3.
- RESET : Hold HIGH for at least two /VCK pulses to reset the chip.
- T1, T2 : Test mode pins (set T1=GND, T2= N.C.)
- DAOUT : Analog output from internal DAC. 5Vp-p @ Vdd=+5V.
Sample rate selection:
S1 S2 0 0 : XT / 96 0 1 : XT / 64 1 0 : XT / 48 1 1 : (Not documented)For a 384 KHz clock source, these are 4, 6, and 8 KHz respectively.
MSM5205 configuration
- 4B//3B tied to +5V (4-bit sample format selected)
- S1 tied to +5V, S2 tied to GND (internal clock divider set to 48)
- Test mode pins are not used
- ASIC drives XT, /RESET, and inputs /VCK. /XT is not used.
DRAM configuration
The CPU interface to ADPCM RAM looks like a 64Kx8 array. However to the chip it is a 128Kx4 array, and samples can start on any nibble boundary. The sample length is always specified in byte (two-sample) units.
MSM5205 timing
Typically the MSM5205 is used with a 384 KHz resonator, and a divider of 48 provides an effective sample rate of exactly 8,000 Hz. However, the PCE implementation provides a programmable clock (effectively over- or underclocking the chip) to allow more sample rates to be selected.
The ASIC divides a 1.540,200 MHz clock to provide the clock signal fed to the MSM5205 XT pin. The divider is set by writing to the lower 4 bits of $180E:
$180E Divider XT frequency Sample rate (XT/48) $00 16 96,270 Hz 2,005.46875 Hz $01 15 102,680 Hz 2,139.166667 Hz $02 14 110,020 Hz 2,292.083333 Hz $03 13 118,480 Hz 2,468.333333 Hz $04 12 128,350 Hz 2,673.958333 Hz $05 11 140,020 Hz 2,917.083333 Hz $06 10 154,020 Hz 3,208.75 Hz $07 9 171,140 Hz 3,565.416667 Hz $08 8 192,530 Hz 4,010.8375 Hz $09 7 220,030 Hz 4,583.958333 Hz $0A 6 256,700 Hz 5,347.916667 Hz $0B 5 308,050 Hz 6,417.708333 Hz $0C 4 385,050 Hz 8,021.875 Hz $0D 3 513,400 Hz 10,695.8 Hz $0E 2 770,100 Hz 16,043.75 Hz $0F 1 1,540,200 Hz 32,087.5 Hz
To determine how much playback time you get for each sample rate, divide the total number of samples that can be contained in RAM (131,072 samples) by the sample rate to get the playback time in seconds.
Note: According to the TurboDuo schematics there is a 9.21 MHz ceramic resonator connected to the ASIC. Assuming it is divided by 6 before being adjusted by $180E, that gives the base frequency of 1.535 MHz for ADPCM decoding. My measurements were at the XT pin, and seem to be close enough.
ADPCM format
The Oki ADPCM format is identical to the Intel/Dialogic VOX format. The 'Sound eXchange' utility ('sox') supports this format and the non-standard sample rates the PCE uses.
The VOX format has no header or other information to specify the sample rate, so that must be explictly stated during conversion. Some examples are as follows:
; Convert 8 KHz ADPCM data to WAV file sox -r 8000 test.vox test.wav ; Convert WAV file to 32 KHz ADPCM data sox music.wav -r 32000 music.vox
The resulting headerless VOX file can be directly included into a program as binary data and stored to ADPCM RAM for playback.
